The design of detecting voltage of single piece fuel - cell 燃料電池堆單片電壓巡檢系統設計
Based on the new method , a digital meter of detecting voltage fluctuation and flicker is implemented with single chip microprocessor 基于新的檢測方法,設計了用單片機系統實現的電壓波動與閃變微機檢測儀。
The basic concepts and character values of voltage fluctuation and flicker are introduced firstly , and then the common methods of suppress the voltage fluctuation are discussed . further more , the process of extracting voltage fluctuation signal and calculating flicker values is analyzed , and the principle of detecting voltage fluctuation and flicker is detailed . by analyzing and comparing the features of the methods and devices in existence , a new digital detection method is present 論文介紹了電壓波動和閃變的基本概念、特征量以及抑制電壓波動與閃變的常用方法,從電壓波動信號的提取和閃變值的獲得兩方面系統地闡述了電壓波動與閃變的檢測原理,分析比較了現有測量方法和裝置的特點和優劣,在此基礎上,提出了一種新的數字式微機檢測方法。
By using a counter and an operation microprocessor , this paper analyses the measuring method and designs an instrument of edm sinking process in discharge state . this instrument takes samples of voltage , current signal and strong and weak of high frequency signals of detecting voltage amplitude , translates them into various time pulses in discharging state . and a counting unit turns these pulses into digital signals , then send them to a microprocessor . finally various discharge time percentages are sent to the control tache 通過采樣電火花加工放電間隙的電壓、電流信號和檢測電壓幅值上的高頻信號的強弱,得出反映間隙放電狀態的各種時間脈沖,利用計數器分別對其計數,再送給單片機運算處理,輸出控制環節所需的各種放電狀態時間百分?jǐn)?shù)。
Abstract : by using a counter and an operation microprocessor , this paper analyses the measuring method and designs an instrument of edm sinking process in discharge state . this instrument takes samples of voltage , current signal and strong and weak of high frequency signals of detecting voltage amplitude , translates them into various time pulses in discharging state . and a counting unit turns these pulses into digital signals , then send them to a microprocessor . finally various discharge time percentages are sent to the control tache 文摘:通過采樣電火花加工放電間隙的電壓、電流信號和檢測電壓幅值上的高頻信號的強弱,得出反映間隙放電狀態的各種時間脈沖,利用計數器分別對其計數,再送給單片機運算處理,輸出控制環節所需的各種放電狀態時間百分?jǐn)?shù)。
It is composed of a cvt embedded voltage monitor and voltage quality analysis software . the monitor can detect voltage amplitude and voltage harmonics on line , and record waveform of disturbance voltage . the sampled data can be stored in computer by communication and can be reprocessed by the analysis software 在理論分析研究的基礎上,設計了一種cvt嵌入式電壓質量監測儀,它由cvt嵌入式電壓監測儀和電壓質量監管軟件組成,可以在線檢測電壓幅值和電壓諧波,記錄電壓擾動波形,并在上位機實現數據二次處理和統計管理。